Sometimes it happens that you have to increase the ring size. The reason for this action may be due to the wrong choice of jewelry size. Perhaps someone simply didn’t know the size and couldn’t find the right ring. It happens that the hand has recovered or, conversely, at the time of purchase it was swollen, swollen, and then lost weight. But is it difficult to adjust the product to size? And what is the best way to do this?
Simple and safe option with boring
It is quite possible to increase the size of a ring with a stone in the simplest and safest way - through boring the product. This procedure involves cutting out the inner layer of the tire. It allows you to enlarge your ring by about half a size. The method is ideal for products with decorative and precious stones that have a wide shank.
The process is usually performed using a special machine with a clamp. It is not suitable for rings that are too thin. Only for wide ones. Takes approximately 10-30 minutes. However, this method has its drawbacks. Due to the use of rolling or boring, the thickness of the tire will decrease. It will become thinner than its original thickness.
Determine the correct size
Of course, the best thing when buying such an expensive gift is to know the exact size, or even better, buy it in the presence of the lady of your heart. In this case, you need to keep in mind that your fingers may swell in the morning, especially in hot weather. It can also occur after exercise, as well as at elevated temperatures during illness.
Important! The thickness of the fingers on the left and right hands is different.
If you don’t know the exact size, you can calculate it using simple methods at home:
- A strip 1 cm wide is inserted inside the product. A mark is made with a pencil in the place where one of the edges ends. The length of the marked strip is measured with a ruler. The resulting number is divided by 3.14 - this will be the size of the jewelry.
- The most accurate way at home is to measure the internal diameter with a caliper, but not everyone has one.
- You can measure using coins, if you have them: 1 ruble - size 21, 50 kopecks - size 19.5, 5 kopecks - 19, 10 kopecks - 18, 1 kopeck - size 16.
- The simplest, but not the most accurate, is to measure the size of the ring with a ruler, and you need to take the inner diameter.
Metal inserts
To increase the size of the ring, you can use inserts made of a suitable metal. During the work, the master carefully cuts the shank from below (in the place where it touches the finger). And then he begins to push it apart as much as it will be necessary to increase the size of the decoration. For example, if you need to increase the product by one size, it needs to be expanded by approximately 3.14 mm.
The resulting space is covered with a small piece of metal, completely matching the parameters and appearance of the ring itself. In this case, the joints are treated not only with a laser, but also with fire. To give the jewelry a natural shine, you need to immerse it in a solution with boric acid. After this, you will not even be able to distinguish where the original metal patch is located, and where the factory tire begins.
The type of soldering directly depends on the existing shape of the stone on the product. You can increase the ring size by soldering an insert made of identical metal in at least an hour. Sometimes it takes more time to process a product.
How to stretch rings with stones
When accepting the ring, the specialist checks the quality of the insert. A professional will not accept for rework products that have defects (chips, cracks). The stretching method (insertion, boring, mechanical stretching) is chosen after examining the jewelry. If the quality and type of setting allows, then expensive gems are dismantled.
Increasing size using mechanical rolling method
Increasing the diameter of a decoration with a thin shank by rolling it out is risky. There is no guarantee that the headband will not break when worn, because the use of this technology makes it even thinner. This option is suitable if the width of the rim is 10-12 mm .
The technology of increasing the diameter by mechanical rolling requires special equipment:
- on a machine, using a roller of the required size, roll out the ring's shackle;
- on the crossbar they give the shank a perfectly round shape;
- measure the diameter with a caliper;
- grind the rim with a file or scraper.
The final stage is polishing with paste. When working with cold metal (gold, silver), the diameter is increased by 0.25-0.5 sizes . To roll it out to a larger size, the ring is heated, and the gems are removed before doing this.
Boring
Using this method, rings with a thick shank are increased by half a size. The procedure is simple and the risk of damaging the gemstone is minimal. Jewelers often resort to the method of boring jewelry that has become tight.
When boring, the weight decreases; the jeweler can give the sawn precious alloy to the owner
To increase the diameter by 0.4 mm, the inner surface of the rim is ground off, the outer side is left unchanged. With such a transformation, the design and inlay of diamonds, rubies and other minerals are not at risk of deformation.
Insertion method
The size of a gold or silver ring of high artistic value can be increased by using an insert made of an alloy of a similar grade and color. This method is used if the setting of the gems is difficult; removing them to roll out the ring using a hot method greatly complicates and increases the cost of the jeweler’s work.
The shank is sawed. The cut ring is placed on the crossbar and hammered to the desired size with a special hammer. A piece of gold (silver) of the appropriate standard is inserted and soldered into the resulting gap. The insertion part's dimensions (thickness, width) exactly correspond to the dimensions of the tire.
To prevent the metal from oxidizing and maintaining its shine, the jewelry is boiled in boric acid before soldering. After transformation, the jewelry is bleached. The insertion site is processed with a file and a scraper, carefully removing all irregularities. To ensure that the solder joints are invisible, the surface of the rim is carefully polished with a special paste.
Using the Pinocchio tool
To increase the size of jewelry, a device called “Pinocchio” is often used. During the procedure, a ring is usually put on it and they begin to stretch it by increasing the size of the cone. However, before you increase the ring size using Pinocchio, you need to heat the product. Otherwise, you risk tearing the jewelry or deforming it.
According to experts, this option is perfect for working with wedding rings and products of the most common round shape. On average, such work does not take more than 25-30 minutes.
How to reduce your ring size
If problems arise with how to roll out a ring, and this can only be done in professional salons, then reducing the size can be dealt with at home. Methods used by professionals:
- Tenderloin - part of the shank is removed and the area is sealed;
- compression - the ring is placed on the surface and a compressive mechanism is applied to it;
- insert - complement the reverse side with metal of identical grade and quality.
If for some reason a trip to the jewelry salon is postponed, you can reduce the cut of the ring at home. Purchase special silicone inserts. They are glued to the back of the ring and replaced every month of continuous wear. A cheap way is to apply several layers of clear varnish to the back. Wait until the new layer dries and apply a new one - maximum 10. The problem with home methods is that the manipulations can be noticeable to others. Agree that it will be incredibly uncomfortable if an insert peeks out from under the ring or someone points out traces of varnish on the jewelry.
Application of mechanical stretching of metal
When answering the question of whether it is possible to increase the size of the ring, one cannot help but recall the method of mechanical stretching of the metal. However, the method is not suitable for products with complex decorative patterns. The presence of a small stone in this case is allowed. The ring itself should also not be too wide. Its approximate thickness should not be more than 10 mm.
During the work process, the master usually performs calculations and determines the size. After that, he rotates the fixed decoration on a special crossbar and heats it. Thus, he manages to achieve suitable dimensions of the product. At the end of the procedure, it is necessary to eliminate roughness and uneven areas of the tire. To do this, it is cleaned and polished.
Ways to stretch a ring
Since the method of how to expand a ring at home is not the easiest and gives a guaranteed result, let’s turn to professionals. If there are stones on the jewelry, for example, a diamond ring, then they will need to be temporarily removed so as not to accidentally break or deform. There are 4 stretching methods.
Rolling out
The ring is rolled out to the desired size using a special tool. This method is only suitable for fairly thick products. A thin piece of jewelry may not survive and simply break.
Inserting a piece of material:
- The ring is cut in one place, usually near the sample.
- A piece of metal of the same quality and grade is inserted into the cut site so that the fragment does not differ in appearance.
- The soldering point is welded. The seam is not visible to the naked eye, its thickness does not exceed 0.1 mm
Boring
This is a method in which a portion of the metal is ground off inside the jewelry. The appearance of the product does not change. How much it costs needs to be clarified directly in the workshop.
Stretching with Pinocchio
“Pinocchio” is a special cone-shaped device on which jewelry is placed. Before processing, the ring is heated and pulled onto the cone.
How to increase ring size at home
Changing the size of a product is not as easy as it might seem at first glance. Therefore, in most cases, experts recommend not even trying. There is a huge risk that you will damage the product. In such cases, it is best to contact specialists.
However, if you are still determined, you will need the following tools for the job:
- Special crossbar.
- Gas-burner.
- Small rubber mallet.
But keep in mind that having all these tools does not give any guarantee that you will succeed. First, you need to take the ring and clamp it, for example, with pliers or round nose pliers. Then you need to turn on the burner and heat the product to its characteristic red color. Next, you should leave the decoration for a few minutes so that it cools down a little. And when it is slightly warm, all you have to do is insert it into the crossbar and start rolling.
Possible risks
When increasing the size of the ring with your own hands, you need to take into account the risk of irreversibly damaging the jewelry: the ring may become deformed, the pattern may float, the stones may fade or fall out. Considering the low cost of the corresponding operation in workshops, this risk can hardly be called justified.
Buy jewelry exactly in size, when choosing rings as a gift - contact online jewelry stores (this way, a product that doesn’t fit can be returned or replaced). And don’t rush to change the size of your jewelry during the summer heat or pregnancy.
17.09.21
What products can be rolled out?
Before you start rolling, keep in mind that not all products can be processed in this way. For example, you cannot use rolling for rings with rotating inserts. You should not try this method for bimetallic products. It is not recommended to roll out even if there are inscriptions, engravings and drawings.
If your rings contain stones, you must carefully remove them before performing the procedure. Otherwise, when the ring is stretched, they may leave their “nests” and jump out. At the end of the work, you can return the stones back and securely fix them using pliers, for example.
How much does it cost to stretch a ring?
Jewelers in any salon can stretch the ring. But you shouldn’t take your word for it, because in the worst case, you will lose your favorite ring forever. Be sure to inquire about the following things before entrusting your jewelry:
- way of doing the work;
- quality of the tools used;
- Is there a guarantee?
Important! Depending on the method chosen, part of the ring remains. In reliable shops, the jeweler should give you the part that was removed, and not keep it for himself.
The cost of ring enlargement starts from 600 rubles for a standard procedure (gold engagement ring without inserts). The more expensive the stone, the greater the risks. For a product with a diamond they will demand at least 2 thousand rubles. Specialists will not undertake work on a product that has cracks or chips.
Source
Rings made of precious metals are the most popular gifts for women. Having received such a gift from a loved one, an unpleasant surprise is the wrong size. And sometimes decoration just becomes not enough for you. And then the question arises of how to stretch the ring at home. We will look at possible solutions to this problem in this article.
Reducing the size of jewelry rings:
If suddenly you were given a ring, and it just so happens that it doesn’t quite suit you in size, then returning the gift is somehow wrong, and besides, you liked it, but because it’s too big, or vice versa small you cannot wear your new precious jewelry. But don’t worry, because the problem of a person’s ring being too big is quite common, but this problem can be solved.
Reduce the diameter of a jewelry ring using compression - from 300 rubles.
Reduce the size of a gold ring - from 400 rubles.
It is also possible to insert metal inside the ring - from 1000 rubles (excluding metal).
Today, there are several ways to reduce a ring. This procedure can be carried out by cutting out excess metal. You can also resize the product using compression. But if your jewelry contains precious stones, then the compression method is not suitable. Another way is not to cut metal from the ring, but, on the contrary, to add it. The method is very unusual, but it is universal. That is, by adding metal you can reduce absolutely any ring.
Is it possible to stretch the ring?
If you still end up buying jewelry that is the wrong size, and it cannot be returned or exchanged, then what should you do? How to expand a gold ring at home?
It's not as simple as it seems. What can be done in such a situation?
- You need to find a metal cone of the appropriate size. Clean it thoroughly and polish it.
- Wrap the cone in foil. This is done to ensure that there are no scratches on the product.
- Warm the ring well and put it on the cone.
- By carefully tapping the end of the cone with a hammer, we try to expand the product.
Determine the correct size
Of course, when buying such an expensive gift, it is best to know the exact size, or even better, buy it in the presence of the lady of your heart. In this case, you need to keep in mind that your fingers may swell in the morning, especially in hot weather. It can also occur after exercise, as well as at elevated temperatures during illness.
Important! The thickness of the fingers on the left and right hands is different.
If you don’t know the exact size, you can calculate it using simple methods at home:
- A strip 1 cm wide is inserted inside the product. A mark is made with a pencil in the place where one of the edges ends. The length of the marked strip is measured with a ruler. The resulting number is divided by 3.14 - this will be the size of the jewelry.
- The most accurate way at home is to measure the internal diameter with a caliper, but not everyone has one.
- You can measure using coins, if you have them: 1 ruble - size 21, 50 kopecks - size 19.5, 5 kopecks - 19, 10 kopecks - 18, 1 kopeck - size 16.
- The simplest, but not the most accurate, is to measure the size of the ring with a ruler, and you need to take the inner diameter.
We take into account the features of different jewelry
The most accurate way is to contact a jeweler or jewelry store.
As you can see, the risk of damaging your jewelry is very high, so the most reliable way is to contact a jewelry workshop.
If you need to change your ring size, consider the following points:
Important! Repair of platinum products can only be carried out using special expensive equipment; not every workshop can afford it, so the price will be higher accordingly.
